How to Fix Your Home Painting Mistakes

Painting is undoubtedly one of the quickest and least expensive ways to transform your home. It can update an area, hide flaws, highlight architectural details and so much more.

Even if you follow the 10 commandments of painting, mistakes and problems do happen and hiring a professional to fix your handywork can be costly.

To help you save money, we share tips from a painting expert on how to fix common problems that occur when painting.

The paint is blistering/bubbling  

Fortunately, this type of blister doesn’t hurt, but it can be painful to look at. Paint blisters or bubbles occur when the paint film lifts from the underlying surface.

So, what causes a paint blister? The loss of adhesion between the paint film and surface is usually caused by heat, moisture or a combination of both. And it eventually leads to peeling.

While it can be corrected, you need to figure out what’s causing the problem or it will occur again.

How to fix blistering/bubbling paint

You can scrape and sand the blisters to remove them (if they don’t go down to the substrate). Once the area is smooth, you should apply a coat of primer and then apply the paint.

However, you’ll need to find and remove the source of moisture if the blisters go down to the substrate.

To stop paint from blistering or bubbling, you should always start with a clean, dry surface. Apply primer-sealer over any stains and give it time to dry completely. Always make sure that the paint is completely dry before you expose the surface to moisture.

It’s also recommends using (or installing) exhaust fans or vents in high-humidity areas. 

The paint is cracking or flaking

When you see a hairline crack, don’t ignore it. Cracks in paint can start small, but will worsen over time if they are not fixed. Cracks or flakes can be caused by a variety of issues, including not preparing the surface or applying oil-based paint over latex paint.

Also, if you use a cheap paint, it’s not going to adhere properly or be flexible. Sometimes, the paint is old, or it’s being applied in the wrong environment and, therefore, is drying too quickly.

Extreme cracking is caused when a second or third coat of paint is applied before the previous coat dries completely, or when the undercoat is incompatible with the finish coat.

How to fix cracked or flaking paint

You can use a wire brush or scraper to remove loose paint (if the cracking isn’t down to the substrate). Then, sand the area to feather the edges, prime any bare spots and repaint the surface.

You may need to use a filler if flaking happens in multiple layers of paint. If the cracking goes down to the substrate, remove all of the paint by scraping or using a heat gun, sand the surface until smooth and even, prime, and then repaint with a quality latex paint.

Check how your home loan compares

The paint is spread too thin

Colours are powerful and that’s why your colour choices are important. But it’s also important to use the proper techniques when painting. A common mistake is spreading paint too thin, according to Jenny Burroughs, Senior Product Manager for PPG paints.

Always ensure that your brush is evenly covered but not soaking wet, and follow the paint manufacturer’s instructions for application.

Touch up mistakes

Sometimes, you don’t need to paint a whole room, you just want to touch up a small area. It’s not uncommon to see a noticeable difference in appearance between the original finish and the touched-up areas.

To avoid this, try to clean marks with a soft sponge and liquid detergent before touching up. If it’s possible, use the original batch of paint and a similar applicator to the one used in the original job.

Deck staining issues

Interior paint isn’t the only place you can run into issues, either. Staining a newly replaced deck can produce undesirable results.

People do not allow for proper curing time. Once cured, they also don’t know that they have to remove the mill glaze prior to staining.

Allow 30 to 60 days for new boards to cure. Most homeowners aren’t aware that the new decking has a mill glaze (a glossy film that forms on the deck). The glaze can be removed with a wood deck cleaner, but this is another area prone to mistakes.

People often wash a deck with bleach and don’t neutralize the bleach with a wash prior to staining. Also don’t use a pressure cleaner since it will impregnate the wood with water. For the best finish, allow the deck to dry to 20% moisture, and then apply two new coats of stain.

Tell us: Enjoyed this article? Don’t forget to like and share.

And while you’re here, take our mortgage shredder challenge and discover how much you can save on your home and investment loans by using loansHub technology as your personal mortgage manager. To discover why loansHub and what we do, click here.

This article via Freshome does not constitute advice; readers should seek independent and personalised counsel from a trusted adviser that specialises in property, a tax accountant and property design specialist.